TI-Nspire Bricked
Voir le premier message non lu • 9 messages
• Page 1 sur 1
TI-Nspire Bricked
Hello. I do not know if this is the right section, but I have an important question. I installed nLaunch using the switchpack, and everything was going fine for several weeks(2?). Today, I was switching from the CAS os I had installed to the regular OS, and my calculator got stuck in an infinite loop. I backed it up, and formatted it. I think this was a huge mistake. I then proceeded to install OS 3.6550, and it has stopped working. Any workarounds, or is my TINSPIRE CX bricked? Thanks. The boot code is 3.24 Thanks in advanced!
-
JayThePro
Niveau 2: MI2 (Membre Initié)- Messages: 5
- Inscription: 09 Avr 2014, 00:47
- Genre:
- Calculatrice(s):→ MyCalcs profile
- Classe: High School
Re: TI-Nspire Bricked
What is _exactly_ its current state ?
-
LevakAdmin
Niveau 14: CI (Calculateur de l'Infini)- Messages: 6414
- Images: 22
- Inscription: 27 Nov 2008, 00:00
- Localisation: 0x1AACC355
- Genre:
- Calculatrice(s):→ MyCalcs profile
- Classe: BAC+5: Epita (ING3)
Re: TI-Nspire Bricked
Thanks for the fast reply! I'll start from the beginning, as I wasn't clear in my before post. Today in math, we were practicing for upcoming state exams. I began to switch from the CAS v3.1 OS to the Non-Cas v3.6, renaming the phoenix.old to phoenix. After I did that, I accidentally clicked for the calculator to "run" phoenix. It failed, due to obvious reasons. I then reset the calculator, and it got stuck in and infinite loop, stopping at the screen of the timer on the "chains". The clock doesn't spin at all. I knew something was wrong, and turn it off. About an hour ago, I backed up my documents, and formatted the whole thing. I then began to install the Non-Cas OS 3.6 in hopes of a turnaround. It failed, and the calculator doesn't get past the spinning clock. That is it's current state.
-
JayThePro
Niveau 2: MI2 (Membre Initié)- Messages: 5
- Inscription: 09 Avr 2014, 00:47
- Genre:
- Calculatrice(s):→ MyCalcs profile
- Classe: High School
Re: TI-Nspire Bricked
Launch the diagnostic menu and then reboot, it will solve all your problems.
-
LevakAdmin
Niveau 14: CI (Calculateur de l'Infini)- Messages: 6414
- Images: 22
- Inscription: 27 Nov 2008, 00:00
- Localisation: 0x1AACC355
- Genre:
- Calculatrice(s):→ MyCalcs profile
- Classe: BAC+5: Epita (ING3)
Re: TI-Nspire Bricked
How Exactly?
-
JayThePro
Niveau 2: MI2 (Membre Initié)- Messages: 5
- Inscription: 09 Avr 2014, 00:47
- Genre:
- Calculatrice(s):→ MyCalcs profile
- Classe: High School
Re: TI-Nspire Bricked
Hold down the reset button and + + at the same time. While holding these down, release the reset button.
-
LegimetProgrammeur
Niveau 2: MI2 (Membre Initié)- Messages: 13
- Inscription: 12 Déc 2013, 02:49
- Genre:
- Calculatrice(s):→ MyCalcs profile
Re: TI-Nspire Bricked
Nevermind, I figured it out. Thank you!
-
JayThePro
Niveau 2: MI2 (Membre Initié)- Messages: 5
- Inscription: 09 Avr 2014, 00:47
- Genre:
- Calculatrice(s):→ MyCalcs profile
- Classe: High School
-
jaroslavN
Niveau 11: LV (Légende Vivante)- Messages: 111
- Images: 1
- Inscription: 11 Oct 2015, 13:16
- Genre:
- Calculatrice(s):→ MyCalcs profile
-
critorAdmin
Niveau 19: CU (Créateur Universel)- Messages: 41498
- Images: 14703
- Inscription: 25 Oct 2008, 00:00
- Localisation: Montpellier
- Genre:
- Calculatrice(s):→ MyCalcs profile
- YouTube: critor3000
- Twitter/X: critor2000
- GitHub: critor
9 messages
• Page 1 sur 1
Retourner vers Problèmes divers / Aide débutants
Qui est en ligne
Utilisateurs parcourant ce forum: Aucun utilisateur enregistré et 81 invités