π
<-
Chat plein-écran
[^]

[Tuto] [EN/FR] Install/Installer nBoot + ControlX (+Linux)

Regroupement de tous les tutoriaux Nspire.

Re: [Tuto] [EN/FR] Install/Installer nBoot + ControlX (+Linu

Message non lude kittensauce » 05 Oct 2018, 22:47

critor a écrit:196MHz is the highest safe optimal value. Higher frequencies aren't that interesting because :
- a AHB slightly higher than 66MHz is likely to silently but progressively corrupt your NAND data
- and if you lower the AHB, it will be much lower than 66MHz and thus impact the NAND performances

Also, I've already seen some (rare) CX calculators being unreliable at more than 210MHz.
So hard-coding a value much higher than 196MHz in ControlX is dangerous.

Wow. I was considering tweaking Nover's auto-configuration to see if I could make my calculator go a little faster, but now I think I'll just leave it as it is...
critor a écrit:But note that if you have Ndless + Nover set up, you'll calculator will still be overclocked from 196MHz to the highest safe value detected/set in Nover once the OS is launched.

I do have Nover set up already; I was just wondering if there was any way to apply Nover's values before the OS loads. Though, I guess there wouldn't be much of a point.
Thanks for answering my questions. :)
Not to be confused with Harry Truman.
Avatar de l’utilisateur
kittensauce
Niveau 0: MI (Membre Inactif)
Niveau 0: MI (Membre Inactif)
Prochain niv.: 0%
 
Messages: 7
Inscription: 20 Aoû 2016, 20:25
Genre: Homme
Calculatrice(s):

Re: [Tuto] [EN/FR] Install/Installer nBoot + ControlX (+Linu

Message non lude Zeklandia » 08 Oct 2018, 03:49

My calc is a CX non-CAS, hardware revision C. I had successfully installed ControlX + nBoot. Everything was working well. Then I made a mistake somewhere in the midst of using nSwitchOS. Now my Boot1 3.0.0.99 has been replaced with a Boot1.5 4.40.8. Everything still works, but ndless is no longer installed at boot. Because of this, it is not possible to use a CAS OS on my calc.

Is there any way to reflash Boot1 3.0.0.99? Is there another way for nBoot to install ndless into the OS at boot?
Avatar de l’utilisateur
Zeklandia
Niveau 2: MI2 (Membre Initié)
Niveau 2: MI2 (Membre Initié)
Prochain niv.: 0%
 
Messages: 6
Inscription: 04 Avr 2016, 04:21
Localisation: SC, USA
Genre: Non spécifié
Calculatrice(s):
GitHub: Zeklandia

Re: [Tuto] [EN/FR] Install/Installer nBoot + ControlX (+Linu

Message non lude parrotgeek1 » 08 Oct 2018, 05:44

Zeklandia a écrit: my Boot1 3.0.0.99 has been replaced with a Boot1.5 4.40.8

This is LITERALLY not possible; boot1's flash chip is not writable. What I think happened is that ControlX is now disabled. Try reinstalling it along with Boot2 4.0.3, and setting default boot to diags.
My Projects:
nLoaderCAS Patcher for ControlXnLaunchy CXM fork (3.9 CAS on B&W) - News Article
Prototypes:
Upgrade EVT Nspire CAS+Fix keyboard on prototype TI-Nspire CAS Touchpad
- Highlights: Nspire CX Non-CAS OS 3.3, CX OS 4.4 special reformatting installers (both found by me on TI's site)
Discoveries:
Boot1.5 vuln (used in nLoader) • Nspire dev boardsPink CX
Je peux comprendre le français mais je ne peux pas le parler bien.
Avatar de l’utilisateur
parrotgeek1Prog.
Niveau 11: LV (Légende Vivante)
Niveau 11: LV (Légende Vivante)
Prochain niv.: 3.8%
 
Messages: 688
Inscription: 29 Mar 2016, 01:22
Localisation: USA
Genre: Homme
Calculatrice(s):
Classe: university student
GitHub: parrotgeek1

Re: [Tuto] [EN/FR] Install/Installer nBoot + ControlX (+Linu

Message non lude Zeklandia » 08 Oct 2018, 06:45

parrotgeek1 a écrit:
Zeklandia a écrit: my Boot1 3.0.0.99 has been replaced with a Boot1.5 4.40.8

This is LITERALLY not possible; boot1's flash chip is not writable. What I think happened is that ControlX is now disabled. Try reinstalling it along with Boot2 4.0.3, and setting default boot to diags.


I did reinstall ControlX and nBoot. I can boot into any CX non-CAS OS with the supplied Boot2 4.0.3 (I flashed it to both the Boot2 and the ExtnD partitions, either works). I can also boot into Linux. When am at the boot menu, I have the calc boot from the Boot2 4.0.3 image flashed to the ExtnD partition. Still, ControlX + nBoot aren't installing ndless like they did originally and are supposed to. Without ndless, the CX CAS OS 4.5 patcher can't run and the OS crashes and self-deletes. I also have to run the ndless installer manually on non-CAS OSes.

I have attached several pictures of the boot menu:
boot menu.jpg
The boot menu.
boot menu Boot2 partition.jpg
The boot menu's options for the Boot2 partition.
boot menu Diags partition.jpg
The boot menu's options for the Diags partition.
boot menu ExtnD partition.jpg
The boot menu's options for the ExtnD partition.


Here is a picture of what I see in BtMg:
BtMg screen.jpg
The main menu of BtMg.


ControlX is definitely working, it's just not patching the OS correctly:
ControlX loading screen.jpg
The ControlX loading screen. Unrelated to the issue at hand, I turned the CAS option on when I took this picture.


I can use it with CX non-CAS OS 4.5, I just have to install ndlessly manually to get stuff like nClock to run. The whole reason I kept fiddling with this is because I wanted to have a CX CAS OS from 4.0.3 or before, because otherwise nClock's mini clock doesn't work. I didn't realize that OSes after 3.6 need a patcher, and patchers are only available for 4.4 and 4.5. I also had ZLock installed, but it is broken on the newer OSes. In order to delete ZLock, I had to have ControlX boot Boot1 or a newer Boot2 in order to get the OS to self-delete so I could delete ZLock with TI's linking software. Thus, I messed up the setup somewhere in that mix of reflashing the OS and using nSwitchOS. At some point, Boot1.5 4.40.8 took the place of Boot1 3.0.0.99, according to ControlX and BtMg.

However, the status screen still shows Boot1's "Code Version" to be 3.0.0.99:
status screen.png
CX non-CAS OS 4.5's status screen (booted with ControlX, ndless manually installed).
status screen.png (5.31 Kio) Vu 199 fois
about screen.png
CX non-CAS OS 4.5's about screen showing Boot1 3.0.0.99 (booted with ControlX, ndless manually installed).
about screen.png (4.96 Kio) Vu 199 fois
Avatar de l’utilisateur
Zeklandia
Niveau 2: MI2 (Membre Initié)
Niveau 2: MI2 (Membre Initié)
Prochain niv.: 0%
 
Messages: 6
Inscription: 04 Avr 2016, 04:21
Localisation: SC, USA
Genre: Non spécifié
Calculatrice(s):
GitHub: Zeklandia

Re: [Tuto] [EN/FR] Install/Installer nBoot + ControlX (+Linu

Message non lude critor » 08 Oct 2018, 12:05

When installing a CX CAS OS on a CX with nBoot+ControlX, you have to press reset on it first boot, as soon as you get the gray screen after the loading bar reaches 100%.

If you don't or don't do it fast enough, then the OS will start silently erasing itself and then reboot the calculator.
You'll need to have Ndless and the appropriate CAS patcher in the /ndless/startup/ folder for the calc engine to work.

nClock is not tailored for versions 4.x.

If it's to protect your files, you should forget about zLock and use nSonic2MS :
viewtopic.php?f=57&t=17640
Image
Avatar de l’utilisateur
critorAdmin.
Niveau 18: DC (Deus ex Calculatorum)
Niveau 18: DC (Deus ex Calculatorum)
Prochain niv.: 75.4%
 
Messages: 30445
Images: 7115
Inscription: 25 Oct 2008, 00:00
Localisation: Montpellier
Genre: Homme
Calculatrice(s):
Classe: Lycée
YouTube: critor3000
Twitter: critor2000
Facebook: critor.ti

Re: [Tuto] [EN/FR] Install/Installer nBoot + ControlX (+Linu

Message non lude Zeklandia » 08 Oct 2018, 15:30

critor a écrit:When installing a CX CAS OS on a CX with nBoot+ControlX, you have to press reset on it first boot, as soon as you get the gray screen after the loading bar reaches 100%.

If you don't or don't do it fast enough, then it will start silently erasing itself and then reboot the calculator.


I've been doing that. On following boots, the screen will flash red when the CAS patcher runs. It doesn't. Instead it sits on the grey OS loading screen, and after a few seconds, the cursor appears on top of the loading clock, but nothing can move.

critor a écrit:You'll need to have Ndless and the appropriate CAS patcher in the /ndless/startup/ folder for the calc engine t work.


I have ndless in its folder, and I have the CAS patcher in the startup folder. After I run the ndless installer on the non-CAS OS, it immediately runs both the patcher and nClock, the two programs in the startup folder.

critor a écrit:nClock is not tailored for versions 4.x.

If it's to protect your files, you should forget about zLock and use nSonic2MS :
viewtopic.php?f=57&t=17640


I know that nClock isn't tailored for the newer OSes, but I can't run any CAS OS before 4.4 on my calc.

Also, I am now aware that ZLock is obselete.



Thank you all for trying to figure this out!
Avatar de l’utilisateur
Zeklandia
Niveau 2: MI2 (Membre Initié)
Niveau 2: MI2 (Membre Initié)
Prochain niv.: 0%
 
Messages: 6
Inscription: 04 Avr 2016, 04:21
Localisation: SC, USA
Genre: Non spécifié
Calculatrice(s):
GitHub: Zeklandia

Re: [Tuto] [EN/FR] Install/Installer nBoot + ControlX (+Linu

Message non lude parrotgeek1 » 08 Oct 2018, 21:46

If the screen blinks red it means you have the wrong patcher for your OS
My Projects:
nLoaderCAS Patcher for ControlXnLaunchy CXM fork (3.9 CAS on B&W) - News Article
Prototypes:
Upgrade EVT Nspire CAS+Fix keyboard on prototype TI-Nspire CAS Touchpad
- Highlights: Nspire CX Non-CAS OS 3.3, CX OS 4.4 special reformatting installers (both found by me on TI's site)
Discoveries:
Boot1.5 vuln (used in nLoader) • Nspire dev boardsPink CX
Je peux comprendre le français mais je ne peux pas le parler bien.
Avatar de l’utilisateur
parrotgeek1Prog.
Niveau 11: LV (Légende Vivante)
Niveau 11: LV (Légende Vivante)
Prochain niv.: 3.8%
 
Messages: 688
Inscription: 29 Mar 2016, 01:22
Localisation: USA
Genre: Homme
Calculatrice(s):
Classe: university student
GitHub: parrotgeek1

Re: [Tuto] [EN/FR] Install/Installer nBoot + ControlX (+Linu

Message non lude Zeklandia » 08 Oct 2018, 22:30

parrotgeek1 a écrit:If the screen blinks red it means you have the wrong patcher for your OS


I wasn't aware of that. Since ndless doesn't get installed on boot and thus the CAS OSes crash, I can only ever run it on a non-CAS OS. My point was, there is no evidence that it gets run on boot with the CAS OS, and it doesn't even get run on boot with the non-CAS OSes: it runs after I manually run the ndless installer.
Avatar de l’utilisateur
Zeklandia
Niveau 2: MI2 (Membre Initié)
Niveau 2: MI2 (Membre Initié)
Prochain niv.: 0%
 
Messages: 6
Inscription: 04 Avr 2016, 04:21
Localisation: SC, USA
Genre: Non spécifié
Calculatrice(s):
GitHub: Zeklandia

Re: [Tuto] [EN/FR] Install/Installer nBoot + ControlX (+Linu

Message non lude critor » 09 Oct 2018, 00:09

Maybe your calculator is not booting on Boot2 4.0.3 if Ndless doesn't get installed.
Image
Avatar de l’utilisateur
critorAdmin.
Niveau 18: DC (Deus ex Calculatorum)
Niveau 18: DC (Deus ex Calculatorum)
Prochain niv.: 75.4%
 
Messages: 30445
Images: 7115
Inscription: 25 Oct 2008, 00:00
Localisation: Montpellier
Genre: Homme
Calculatrice(s):
Classe: Lycée
YouTube: critor3000
Twitter: critor2000
Facebook: critor.ti

Re: [Tuto] [EN/FR] Install/Installer nBoot + ControlX (+Linu

Message non lude Zeklandia » 09 Oct 2018, 00:17

critor a écrit:Maybe your calculator is not booting on Boot2 4.0.3 if Ndless doesn't get installed.


But if I have flashed Boot2 4.0.3 to the Boot2 partition and ExtnD, even if I am choosing to boot from ExtnD and for some reason it isn't, what else is it booting from? How can I verify what is booting if ControlX can't tell?
Avatar de l’utilisateur
Zeklandia
Niveau 2: MI2 (Membre Initié)
Niveau 2: MI2 (Membre Initié)
Prochain niv.: 0%
 
Messages: 6
Inscription: 04 Avr 2016, 04:21
Localisation: SC, USA
Genre: Non spécifié
Calculatrice(s):
GitHub: Zeklandia

PrécédenteSuivante

Retourner vers Tutoriaux

Qui est en ligne

Utilisateurs parcourant ce forum: Aucun utilisateur enregistré et 3 invités

-
Rechercher
-
Sujets à la une
Triconcours universel de la rentrée - 2000 euro de prix !
"NumWorks++": Challenge de modification matérielle pour rajouter une puce de mémoire Flash !
Offre TI-Planet/Jarrety pour avoir la TI-83 Premium CE avec son chargeur pour 79,79€ port inclus !
Offre TI-Planet/Jarrety pour avoir la TI-Nspire CX CAS à seulement 130€ TTC port inclus!
Jailbreake ta TI-Nspire avec Ndless et profite des meilleurs jeux et applications !
Transforme ta TI-Nspire CX en console Game Boy Advance!
123456
-
Donations/Premium
Pour plus de concours, de lots, de tests, nous aider à payer le serveur et les domaines...
PayPal : paiement en ligne sécurisé - secure online payments
Découvrez les avantages d'un compte donateur !
JoinRejoignez the donors and/or premium!les donateurs et/ou premium !


Partenaires et pub
Notre partenaire Jarrety 
-
Stats.
408 utilisateurs:
>348 invités
>55 membres
>5 robots
Record simultané (sur 6 mois):
6892 utilisateurs (le 07/06/2017)
-
Autres sites intéressants
Texas Instruments Education
Global | France
 (English / Français)
Banque de programmes TI
ticalc.org
 (English)
La communauté TI-82
tout82.free.fr
 (Français)